COLOR TV RECEIVER
OWNER'S MANUAL
The Owner`s Manual for the Follow Models:
21F9D-P, 21T9D-P,21F9D,21T9D,1407
Please READ this manual carefully
before operating the unit, and keep
it for future reference.
Warning and cautions
1. When you clean the TV set, please 4. Do not place the TV set near rain or
pull out the power plug from AC outlet.
Don't clean the cabinet and the
screen with benzene, petrol and other
chemicals.
moisture as it may cause an electric
shock, or the TV set to catch fire. The
TVsetmustonly
beusedindryin
door locations.
2. In order to prolong the using life of
the TV set, please place it in a well
ventilatedlocation.
5. The back cover must only be
removed by a registered electrical
service person. Removing the back
cover may result in electric shock, fire
or damage to
the TV set.
6. If the TV set is not going to be used
for a long time, or there is a severe
thunder & Lighting storm, it is
recommended that the TV set be
disconnected from the AC power outlet
and the aerial plug removed.
3. Don't place the TV
set in direct sunlight
ornearaheatsource.
Explanation on the display tube
In general, it is not needed to clean the tube surface. However, necessary,
it's surface can be cleaned with a dry cotton cloth after cutting off the power.
Don't use any cleanser. If using hard cloth, the tube surface will be damaged.
Installation
Aerial connection
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV
system or an outdoor antenna .In different places, the suitable antenna type and position
are different.
300 twin-lead cable
Antenna adapter
(additional purchase)
Mixer
additional
purchase
75
coaxial cable
Antenna input
75 standard
coaxial type
Plug
(additional purchase)
AC power socket
Note
* It is recommended that you'd better use 75 coaxial cable to remove the
disturbance caused by airwave.
* Don't bind antenna cable and power wire together.
Preparation of the remote control unit
Battery installation
Take off the battery compartment cover. Place two AAAbatteries, make sure that battery
polarity matches with the +/- mark inside the battery compartment.
Operation notes for the remote control unit
Under normal conditions, the life time of batteries is one year.
If you don't intend to use the unit for a long period or the electricity of the batteries is
used up, remove the batteries to prevent batteries acid from leaking into the battery
compartment.
Don't throw your batteries into a fire. Dispose of your batteries with a specified method.
Avoid the falling and the wetting of the remote control unit.
Function buttons and external sockets
Front and side panel of the TV set
1407
VIDEO R-AUDIO-L
Power switch
Signal receiver
Power indicator
Video R/L Audio
TV/AV
MENU
VOL-
VOL+
CH-
CH+
Menu
TV/AV
switching
Volume up/ down
Channel position up/down
21F9D, 21F9D-P,
21T9D, 21T9D-P
VIDEO
Video Input
terminal
L
Audio Input
terminal
AUDIO
R
Power indicator Sensor window Power switch
MENU
AV/TV
(input selector
Volume up/ down
Channel selector
Note: The cabinet and buttons of TV is only for reference.
Rear panel of the TV set
EXT
Antenna input
TV SCRAT Terminal
If you want to connect the TV set to the other audio/video equipment, please
refer to P22.
Buttons on the remote control
Buttons and Descriptions
MUTE
POWER
Mute Button
CALL
SWAP
Press to concealthe sound ofprograms.
Stand by Button
TV/AV
-/--
Screen Display Button
Swap function Button
TV andAV Exchange Button
To exchanger betweenTV and
other available videoinputs
Digital selector
1
4
2
5
8
0
3
6
7
SCAN
9
TIME
Program number Button
Program scan Button
Time menu
P.STD
FUNCTION
Picture mode selection
Function menu
CH+
Menu Select/Adjust Button
Use this buttonto adjust themenu,
the volume andthe channels.
Tune menu
VOL
-
VOL
+
MENU
CH-
Picture menu
PICTURE
TUNE
EXIT
Exit screen display
Switching on/ off the TV set
In the following, the methods of using power switch and remote controller to switch
on/off power supply for the TV set will be explained.
Switching on/ off the TV set
Switching on/ off the TV set
1 Please press the power switch to switch on AC
power supply and the power indicator will light.
2 If the indicator is lighting in red, press the POWER
button on the remote control again.
Note
1 When you don't operate the TV set with a
remote control, you can turn on it directly
through pressing the P+/- buttons on the TV set
(Child Lock must be turned off).
4
AUTO
BG
2 If you want to exchange to standby status,
please press down the POWER button on the
POWER
remote control.
3 If you want to fully switch off the power supply
for the TV set, please press the power switch
button on the TV set.
Auto switch-off function
When the "Back" function is on, if an empty
channel is selected or the TV programs are
ended for the day, the power will be switched off 5
minutes later automatically. If the "OFF TIME" is
on, it will be switched off according to the
presetting time. The auto power off function does
not work under video input or when the
background is off.
(Note: If the "off timer" is less than 5 minutes, it
will be switched off automatically to the preset
Time. )
Watching TV
You can watch TV program in a preset channel.
Watching TV program
How to select TV program
Select the desired program
1 Using "Program number" buttons
1
4
7
2
5
8
0
3
6
9
Directly enter thechannel number withthe numeric keypad
on the remotecontrol.
To select channel numbersfrom 10 ~99 press [-/--]button
and enter thetwo digit channelnumber
To select channel numbersfrom 100 ~218 press [-/--]button
twice and enterthe 3 digitchannel number
2 Using the CH+/- buttons
Press the CH+ button to select a channel number in number
increasing direction.
Press the CH- button to select a channel number in number
decreasing direction.
CH+
Select the desired sound
VOL
-
VOL
+
MENU
Press the VOL-/+ buttons on the remote or the front of the
TV set to adjust the volume level.
CH-
If the colour or sound of a channel is abnormal
The settings of the colour
TUNE
system or the sound system
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
OFF
0
may be wrong.
Press the TUNE button and
setting menu shown on the
right will display on the screen.
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
CH+
If picture colour is abnormal
VOL
-
VOL
+
Use the CH+/- buttons to select Colour then the
VOL-/+ buttons to select the colour system.. Press the
EXIT button to save the setting.
MENU
CH-
If the picture sound is abnormal
Use the CH+/- buttons to select Sound then press the
VOL-/+ buttons to select the sound system.
Watching TV continued
Swapfunctionenablesquickswaptothelastwatchedprogram.
Auto scan function enables automatic successive scanning of all the programs in
memorywith "OFF"skipstatus(eachchannelwilllastabout2seconds).
Program swap and auto scan functions
Program swap
1 Suppose the channel number
you used just now is 8 and the
channel number you are using
is 18 (as shown in the figure).
18
AUTO
BG
SWAP
8
AUTO
BG
2 If you want to return to the
last watched program channel
8, you can simply press the
SWAP button.
18
AUTO
BG
3 If you want to return to
channel 18, press the button
again. Through this function,
you can easily change
between the channel you are
using and the channel you
used last time.
Auto program scan
1 If you want to select a
desirable program, you may
scan all the TV programs in
memory. You can simply press
the SCAN button to do this. The
programs will appear one after
another from beginning to end
(each channel number will last
about 2 seconds).
1
AUTO
BG
SCAN
2
AUTO
BG
SCAN
SCAN
3
AUTO
BG
SCAN
1
AUTO
BG
2 If you want to stop the function
during auto scanning, simply
presstheSCANbutton again.
Searching channel
This TV set has three methods to set the channels, which are respectively full
automatic, semi automatic and manual fine tune.
-
In this section, how to use the remote control to set the channel is explained. You
can also use the buttons on the TV set to set channel.
Full automatic mode
1 Press the TUNE menu button ,
TUNE
till the TUNING menu shown on
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
OFF
0
the right display on the screen.
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
2 Press the CH+/- buttons to
select "AUTO SEARCH".
CH+
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
OFF
0
VOL
-
VOL
+
MENU
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
CH-
3 Press the VOL+ button to
ensure automatic search
function operates. All channels
now playing program will be
automatically preset in order .
After the search has finished,
the first program number will
display on the screen.
Display function
CALL
Press the CALL button, then
the channel number and the
systems will be displayed on
the screen.
4
AUTO
BG
Searching channel
Continued
Semi-automatic search
Semi-automatic search
1 Press the CH+/- buttons or
PROGRAM NUMBER 0-9
buttons to choose desired
channels I.E. channel 1
1
AUTO
BG
TUNE
2 Press the TUNE menu button ,
till the TUNING menu shown on
the right display on the screen.
3 Press the CH+/- buttons to
select " SEARCH".
CH+
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
OFF
0
VOL
-
VOL
+
MENU
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
CH-
4 Press the VOL-/+ buttons to
1
start searching.
The VOL- down button is used
for lower side program search.
The VOL+ up button is used for
higher side program search.
Repeat this step, till find the
desired channel.
To turn off the on-screen menu
In general, after you press the MENU button, the menu item
display (PICTURE, TIME, FUNCTION, TUNE, EXCHANGE,
ETC.) will automatically disappear within 15 seconds. If you
want to eliminate these contents immediately, please press
the EXIT button.
EXIT
Searching channel
Continued
Manual fine tune
Manual fine tune
If the picture and/or sound are poor, try using the FINE
TUNE feature. Do not use this feature unless
reception is poor.
CH+
1 Press the CH+/- buttons or
PROGRAM NUMBER 0-9
button to choose desired
channels I.E. channel 1
1
AUTO
DK
VOL
-
VOL
+
MENU
CH-
2 Press the TUNE menu button ,
till the TUNING menu shown on
the right display on the screen.
TUNE
3 Press the CH+/- buttons to
select " FINE TUNE".
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
OFF
0
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
CH+
VOL
-
VOL
+
MENU
CH-
4 Press the VOL-/+ buttons all
through to carry out fine tune,
till the best picture and sound
are obtained.
1
FINE TUNE
152.25MHz
Searching channel
Continued
Program skip
Program skip
The Program skip feature enables you to skip/hide
programs that you do not wish to be displayed when
using the CH+/- buttons. These channels will still be
displayed by directly using the channel number
buttons on the remote control.
CH+
1 Press the CH+/- buttons or
PROGRAM NUMBER 0-9
button to choose desired
channels I.E. channel 1
1
AUTO
BG
VOL
-
VOL
+
MENU
CH-
2 Press the TUNE menu button ,
till the TUNING menu shown on
the right display on the screen.
TUNE
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
OFF
0
3 Press the CH+/- buttons to
select "SKIP".
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
4 Press the VOL-/+ buttons to
turn the SKIP function "ON".
CH+
TUNE
COLOUR
SOUND
BAND
AUTO
BG
VHFL
ON
VOL
-
VOL
+
MENU
5 Press the TUNE button to close
the menu. When you use the CH+/-
buttons to select channel, this
channel will be skipped. However,
you can still use the PROGRAM
NUMBER buttons to select the
skipped channel numbers.
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
0
CH-
If you want to recover the skipped channel
1 Use the PROGRAM NUMBER buttons to select the channel
number to be recovered.
2 Repeat those steps just now.
3 Press the VOL-/+ buttons to turn the SKIP function "OFF".
Convenient picture and sound control functions
Multiple picture modes
How to select picture modes
You can quickly select the desired picture mode from
four preset modes and one customized mode.
P.STD
Press the P.STD button to select the
STANDARD
desired picture quality. Five kinds
RICH
of picture modes (i.e., "STANDARD",
"RICH", "USER","LISTEN",
USER
"SOFT" ) can be selected in turn.
LISTEN
SOFT
How to customize your own picture status
1 Press the PICTURE menu button , till the PICTURE menu
PICTURE
shown on the right display on the screen.
2 Press the CH+/- buttons to
PICTURE
select the item to adjusted,
then press the VOL-/+ buttons
to obtain the desired effect.
CONTRAST
BRIGHTNESS
COLOUR
SHARPNESS
*HUE
48
32
48
40
60
CH+
VOL
-
VOL
+
MENU
BLACK STRETCH OFF
CH-
I T E M
Press VOL-
Press VOL+
Strong
Weak
CONTRAST
BRIGHTNESS
COLOUR
Bright
Dark
Deep
Shallow
Soft
Sharp
SHARPNESS
*Hue
lean to green
lean to purple
Note:
The "Hue" item only appears when the colour system is NTSC.
Convenient picture and sound control functions
Continued
Black Stretch-(Automatically Increases the Contrast Rage)
Noise Reduce - (Picture Noise & Grain Reduction Circuit. Only use on poor reception.)
Black stretch and noise reduce
How to select BLACK STRETCH
PICTURE
1 Press the PICTURE menu
button , till the PICTURE menu
PICTURE
shown on the right display on the
CONTRAST
BRIGHTNESS
COLOUR
48
32
48
40
60
screen.
SHARPNESS
*HUE
CH+
BLACK STRETCH OFF
2 Press the CH+/- button to
select "BLACK STRETCH".
VOL
-
VOL
+
MENU
CH-
PICTURE
CONTRAST
BRIGHTNESS
COLOUR
SHARPNESS
*HUE
48
32
48
40
60
3 Press the VOL-/+ buttons to
turn the BLACK STRETCH
function "ON" or "OFF".
BLACK STRETCH ON
How to select NOISE REDUCE
1 Press the FUNCTION menu
button, till the FUNCTION menu
FUNCTION
shown on the right display on the
ENGLISH
FUNCTION
screen.
BACKGROUND
NOISE REDUCE
FADE
CHILD LOCK
AVL
CALENDAR
ON
ON
ON
OFF
ON
CH+
2 Press the CH+/- buttons to
select "NOISE REDUCE".
VOL
-
VOL
+
MENU
FUNCTION
ENGLISH
BACKGROUND
NOISE REDUCE
FADE
CHILD LOCK
AVL
CALENDAR
CH-
ON
OFF
ON
OFF
ON
3 Press the VOL-/+ buttons to
turn the NOISE REDUCE
function "ON" or "OFF".
Convenient picture and sound control functions
Continued
Mute function
Sound mute
1 Press the MUTE button on the
remote control and "MUTE" type
MUTE
face will display on the lower part
of the screen. At this time, the
sound of the TV set is turned off.
MUTE
2 If you want to recover the sound,
press the MUTE button again or
directly press the VOL-/+ buttons.
Time functions
Clock setting and timer on/off functions
Clock setting
The clock will only work if the TV set if left turned on
or in standby. When the set is disconnect from the
power supply or is turned off by the main power on
the front panel, the clock losespower and will need to
be reset when the power is reconnected.
TIME
1 Press the TIME menu button,
and the TIME menu display on
the screen.
CH+
TIME
CLOCK
17:18
18:00
1
VOL
-
VOL
+
MENU
2Press the CH+/- buttons select ON TIME
"CLOCK", then press the VOL -
/+ buttons to adjust the time in
hour position; press again the
CH+/- buttons to select the
time in minute position, then
press the VOL -/ +buttons to
adjust the value of minutes .
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
--:--
0
--:--
1
CH-
On/off timer
Using on/off timer function, the TV set can automatically
turn on to a preset program or shut down in a preset time.
1 Press the TIME menu button
to call up the TIME menu on the
screen.
TIME
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
17:18
18:00
1
--:--
0
2 Press the CH+/- buttons to
select "ON TIME", then press
the VOL -/+ buttons to set the
value in hour position; press
again the CH+/- buttons to
select the minute position and
set the value of the minute.(take
18:00 as an example)
--:--
1
CH+
VOL
-
VOL
+
MENU
3 Press the CH+/- buttons to
select "ON PROG", then press
the VOL-/+ or program direct
number buttons to select your
desired channel (take 8 as an
example).
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
CH-
17:18
18:00
8
23:00
0
--:--
1
4 Repeat step 1-2 to set OFF
TIME.(take 23:00 as an example)
Time functions
Continued
Sleep timer and program preset
Sleep timer
The TV set have 18 sections
0
option for sleep timer function
(each section has a time
interval of 10 minutes) (See right
chart):
10
20
TIME
170
180
1 Press the TIME menu button,
and the TIME menu display on
the screen.
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
CH+
2 Press the CH +/- buttons to
select "SLEEP TIMER".
17:18
18:00
8
23:00
120
--:--
1
VOL
-
VOL
+
MENU
CH-
3 Press the VOL -/+ buttons to
SLEEP TIMER
adjust the SLEEP TIMER level. REMIND TIME
REMIND PROG
REMIND PROG function
Program remind timer, that displaysan on-screen reminder
prompt, when aprogram on adifferent channel is due tostart.
1 Press the TIME menu button
to call up the TIME menu on the
screen.
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
TIME
17:18
18:00
8
23:00
120
2 Press the CH +/- buttons to
select "REMIND TIME", then
press the VOL -/+ buttons to
set the value in hour position;
press again the CH+/- buttons
to select the minute position,
and then set the value of the
minute.(take 19:00 as an
example)
19:00
1
CH+
VOL
-
VOL
+
MENU
3.Press the CH+/- buttons to
select "REMIND PROG", then
press the VOL -/+ buttons or
the program direct number
buttons to set the desired
channel (take 18 as an
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
17:18
18:00
8
23:00
120
CH-
19:00
18
example).
NOTE: For REMIND PROG to
operate CHILD LOCK must be
turned off.
Set up function
Screen saver and childlock functions
How to start screen saver function
When the BACKGROUD function
is ON, the screen will turn
automatically as shown "NO
SIGNAL" of moving .
NO SIGNAL
1 Press the FUNCTION menu
FUNCTION
button till the FUNCTION menu
,
shown on the right display on the
screen.
FUNCTION
ENGLISH
2 Press the CH+/- buttons to
select "BACKGROUND" and press
the VOL-/+ buttons to turn the
BACKGROUND function "ON" .
BACKGROUND
NOISE REDUCE
CHILD LOCK
AVL
ON
ON
OFF
ON
CH+
CALENDAR
VOL
-
VOL
+
MENU
CH-
Child lock function
Enables the TV front control buttons to be locked.
1 Press the FUNCTION menu
FUNCTION
button till the FUNCTION menu
,
shown on the right display on the
screen.
2 Press the CH+/- buttons to
select "CHILD LOCK" and press
the VOL-/+ buttons to turn
CHILD LOCK function "ON" .
CH+
FUNCTION
ENGLISH
BACKGROUND
NOISE REDUCE
CHILD LOCK
AVL
ON
ON
OFF
ON
VOL
-
VOL
+
MENU
CALENDAR
CH-
NOTE:
All the control panel buttons on the front of the TV are disabled
when CHILD LOCK is turned on. The power switch will still turn
the TV set off.
Set up function
Continued
AVL and calendar functions
AVL function
1 Press the FUNCTION menu
FUNCTION
button till the FUNCTION menu
,
shown on the right display
on the screen.
FUNCTION
ENGLISH
BACKGROUND
NOISE REDUCE
CHILD LOCK
AVL
ON
ON
OFF
ON
CALENDAR
CH+
VOL
-
VOL
+
MENU
2 Press the CH+/- button to select
"AVL" .
FUNCTION
ENGLISH
CH-
3 Press VOL-/+ button to turn the
BACKGROUND
NOISE REDUCE
CHILD LOCK
AVL
ON
ON
OFF
ON
AVL function "ON" or "OFF"
.
CALENDAR
Calendar function
FUNCTION
1 Press the FUNCTION menu
button till the FUNCTION menu
,
shown on the right display on the
screen.
FUNCTION
ENGLISH
BACKGROUND
NOISE REDUCE
CHILD LOCK
AVL
ON
ON
OFF
ON
2 Press the CH+/- button to select
"CALENDAR" , then press the
VOL-/+ buttons to the CALENDAR
display on the screen.
CALENDAR
CH+
VOL
-
VOL
+
MENU
3 Press the VOL-/+ buttons to turn
the YEAR/MONTH/DAY, press
CH+/- buttons to set or adjust
the YEAR/MONTH/DAY.
CH-
Set up function
Continued
Select a language
Select a language
FUNCTION
1 Press FUNCTION menu
button till FUNCTION menu
,
shown on the right display
on the screen.
FUNCTION
ENGLISH
BACKGROUND
NOISE REDUCE
CHILD LOCK
AVL
ON
ON
OFF
ON
2 Press the CH+/- buttons to
CH+
CALENDAR
select "
" .
VOL
-
VOL
+
MENU
CH-
3 press the VOL-/+ buttons to select
the desired language. Then all the
items will be displayed in the
selected language.
Position exchange functions
Exchange
Exchange
This feature enables TV programs that may be on a wrong TV
channel number to be swapped/exchanged. This feature is
very useful when Automatic Search Tuning has been used, to
reallocate the found programs to the correct channel numbers.
CH+
1 Press the MENU button till the
,
EXCHANGE menu display on
the screen.
VOL
-
VOL
+
MENU
EXCHANGE
PROGRAM 1
PROGRAM 2
EXCHANGE
6
2
CH-
2 Press the VOL-/+ buttons or the
PROGRAM NUMBER 0-9
buttons to set PROGRAM 1 TO 6.
3 Press the CH-/+ buttons to
select " PROGRAM 2".
CH+
VOL
-
VOL
+
MENU
4 Press the VOL-/+ buttons or
the PROGRAM NUMBER 0-9
buttons to set PROGRAM 2 TO 9.
CH-
EXCHANGE
PROGRAM 1
PROGRAM 2
EXCHANGE
6
9
5 Press the CH+/- buttons to
select "EXCHANGE".
CH+
VOL
-
VOL
+
MENU
6 Press the VOL-/+ buttons to set
"EXCHANGE".
CH-
EXCHANGE
PROGRAM 1
PROGRAM 2
EXCHANGE
6
9
Connecting the TV set to the other video and audio equipment
Connecting to the other video and audio equipment
EXT
To TV EXT
To TV EXT
To outside input
To video/audio input
DVD, VCD and other reproducing equipment
Stereo
Troubleshooting guide
To assist in location possible faults use help guide below.
BREAKDOWN PHENOMENON
CHECKING
PICTURE
SOUND
The aerial direction and connection
Picture with snow
Double or Triple Image
Disturb
Noise
This is called ghosting which can be minimized
with an outside aerial, and good quality cable
and terminations. Altering the aerial direction
can also minimize this effect.
Normal
Noise
Electrical interference which can be caused by cars,
motorbikes etc, Fluorescent lamps and dirty
insulators on overhead power cables.
1. Volume Sound mute.
2. Only 1 speaker has no sound. Press S.STD button to
choose USER mode, then check wether the BALANCE
item value in SOUND menu equal to 0. Adjust the
BALANCE item in SOUND menu as you wish in USER
mode.
No sound or 1
speaker no sound
Normal
Ensure that the power supply is connected to the TV
set and turned on. Also ensure that the TV set isnot
in "Listen Mode" or that the brightness and contrast
are not turned down.
No sound
No Picture
Adjust colour control
Adjust channel again
Normal volume
Normal or Weak Volume
No colour
Scramble
Colour Purity faultwhich can becaused by movingthe
TV set, placingmagnets near theTV screen orturning
on/off house holdappliances such asvacuum cleaners
near the TVset. Turnthe TV off with themains power
switch for 15minutes. When thepower is turnon again
the TV setwill automatically degaussthe picture. In
server cases leavethe TV setturned off overnight.
Colour Spot
Normal volume
Note:
1.If the fault can not be repaired using the above guide consult with your local authorized service
center.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to
remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.
3. The cabinet may produce the occasional "snapping sound" This is normal and caused by the
materials in the cabinet expanding with room temperature changes.
Specifications
Colour system
PAL, SECAM
BG, DK, I
1407
14"color picture tube
21"colour picture tube
Picture tube
21F9D, 21F9D-P,
21T9D, 21T9D-P
Sound output power
Power requirements
2W not distortional
1407
~ 110V-250V 50Hz/60Hz
21F9D, 21F9D-P,
21T9D, 21T9D-P
~ 180V-250V 50Hz/60Hz
1407
60W
70W
Power consumption
Dimension
21F9D, 21F9D-P,
21T9D, 21T9D-P
342 Width x371 Depth x318 Height
603 Width x475 Depth x430 Height
mm
mm
1407
21F9D, 21F9D-P,
21T9D, 21T9D-P
Remote control
Owner's manual
Battery(AAA)
X1
X1
X2
Accessories
The design and specifications may be changed without notice.
01
0090506138B
|