Harbor Freight Tools Battery Charger 67031 User Manual

3–5 hour, 18 Volt,  
Battery Pack charger  
67031  
Set uP and oPerating inStructionS  
note: Battery Pack (67029) Sold SeParately.  
®
distributed exclusively by harbor Freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
SaVe thiS manual.  
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any  
artwork contained herein may be reproduced in any shape or form without the express written  
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described  
herein. Tools required for assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
 
1.  
Use on dry, flat, fireproof 8. When battery pack is not in use,  
surface only. The Charger  
gets hot during use. The  
Charger’s heat can build up  
keep it away from other metal  
objects, like paper clips, coins,  
keys, nails, screws or other small  
metal objects, that can make a  
connection from one terminal to  
another. Shorting the battery pack  
terminals together may cause burns  
or a fire.  
to unsafe levels and create a fire  
hazard if it does not receive adequate  
ventilation, due to an electrical fault,  
or if it is used in a hot environment.  
Do not place the Charger on a  
flammable surface. Do not obstruct  
any vents on the Charger. especially  
avoid placing the charger on  
carpets and rugs; they are not only  
flammable, but they also obstruct  
vents under the charger.  
Place the Charger on a stable, solid,  
nonflammable surface (such as a  
stable metal workbench or concrete  
floor) at least 1 foot away from all  
flammable objects, such as drapes or  
walls. Keep a fire extinguisher and a  
smoke detector in the area.  
9. under abusive conditions, liquid  
may be ejected from the battery  
pack; avoid contact. if contact  
accidentally occurs, flush with  
water. if liquid contacts eyes,  
additionally seek medical help.  
Liquid ejected from the battery pack  
may cause irritation or burns.  
10. Do not expose chargers to rain or wet  
conditions. Water entering a Charger  
will increase the risk of electric shock.  
Charge indoors only.  
Frequently monitor the Charger and  
battery pack during use.  
11. Keep charging area clean and well  
lit. Cluttered or dark areas invite  
accidents.  
2. charge only designated battery  
packs; others may overheat, leak,  
or burst.  
12. Do not operate chargers in explosive  
atmospheres, such as in the presence  
of flammable liquids, gases or dust.  
Chargers create sparks which may  
ignite the dust or fumes.  
3. Follow charging instructions.  
4. do not insert damaged battery  
pack.  
13. Charger plugs must match the outlet.  
Never modify the plug in any way.  
Unmodified plugs and matching  
outlets will reduce risk of electric  
shock.  
5. check frequently while charging.  
6. Wear anSi-approved safety  
goggles during use.  
7. Use chargers only with specifically  
designated battery packs. Use of  
any other battery packs may create a  
risk of injury and fire.  
14. Do not abuse the cord. Never use  
the cord for carrying, pulling or  
unplugging the Charger. Keep cord  
away from heat, oil, sharp edges or  
moving parts. Damaged or entangled  
cords increase the risk of electric  
shock.  
SKU 67031  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
15. Store idle chargers out of the reach  
of children and do not allow persons  
unfamiliar with the Charger or these  
instructions to operate the Charger.  
24. WARNING: Handling the cord on  
this product will expose you to lead,  
a chemical known to the State of  
California to cause cancer, and birth  
defects or other reproductive harm.  
Wash hands after handling.  
16. Maintain chargers. Check for  
breakage of parts and any other  
condition that may affect the  
(California Health & Safety Code §  
25249.5, et seq.)  
Charger’s operation. If damaged,  
have the Charger repaired before use.  
SaVe theSe  
inStructionS.  
17. Have your Charger serviced by a  
qualified repair person using only  
identical replacement parts. This will  
ensure that the safety of the Charger  
is maintained.  
18. Inspect before every use; do not use  
if parts are loose or damaged.  
19. Use as intended only.  
20. Unplug after use and before service,  
cleaning or storage.  
21. Maintain labels and nameplates on  
the Charger. These carry important  
safety information. If unreadable or  
missing, contact Harbor Freight Tools  
for a replacement.  
22. This product is not a toy. Keep it out  
of reach of children.  
23. People with pacemakers should  
consult their physician(s) before  
use. Electromagnetic fields in close  
proximity to heart pacemaker could  
cause pacemaker interference or  
pacemaker failure. In addition,  
people with pacemakers should  
properly maintain and inspect to avoid  
electrical shock.  
Page 4  
For technical questions, please call 1-800-444-3353.  
SKU 67031  
 
shown in the preceding illustration.  
(See outlets for 2-Prong Plug.)  
grounding  
improperly  
connecting the  
grounding wire can result in  
electric shock.  
extension cords  
Note: Extension cords must not be used  
with this Charger.  
Check with a qualified  
electrician if you are in doubt  
as to whether the outlet is  
properly grounded. do not  
modify the power cord plug  
provided with the charger.  
do not use the charger if  
the power cord or plug is  
damaged. if damaged, have it  
repaired by a service facility  
before use. if the plug will not  
fit the outlet, have a proper  
outlet installed by a qualified  
electrician.  
Symbology  
Double Insulated  
Canadian Standards  
Association  
Underwriters Laboratories, Inc.  
Volts Alternating Current  
V~  
a
Amperes  
double insulated chargers:  
chargers with two Prong Plugs  
outlets for 2-Prong Plug  
1. Chargers marked “Double Insulated”  
do not require grounding. They  
have a special double insulation  
system which satisfies OSHA  
requirements and complies with the  
applicable standards of Underwriters  
Laboratories, Inc., the Canadian  
Standard Association, and the  
National Electrical Code.  
(See outlets for 2-Prong Plug.)  
2. Double insulated chargers may be  
used in either of the 120 volt outlets  
SKU 67031  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
alignment  
tab  
SPeciFicationS  
Electrical Input  
120 V~ / 60 Hz  
Electrical Output 22 VDC / 500 mA  
Power  
indicator  
Charge Time  
Charging  
3-5 hours  
67029 - 18 V, 1.3 A, NiCd  
Battery Pack (sold separately)  
Capability  
Figure 4B  
unPacking  
4. Slide the Charger onto the Battery  
Pack until it firmly rests in place  
against the alignment tab (see  
When unpacking, make sure that  
the item is intact and undamaged. If any  
parts are missing or broken, please call  
Harbor Freight Tools at 1-800-444-3353 as  
soon as possible.  
Figures 4A and 4B). If the Charger  
does not fit properly, disconnect it  
and confirm that the Battery Pack is  
the correct model for this Charger as  
shown on the Specification chart.  
do not charge any Battery Pack not  
listed or any Battery Pack that the  
Charger does not securely fit.  
oPerating inStructionS  
read the entire imPortant  
SaFety inFormation  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
5. Attach the Cord to the Charger. The  
Power Indicator will light to show that  
the power is connected.  
1. Place the Battery Pack on a dry  
fireproof surface in a room where the  
temperature is from 50–104° F.  
6. For a fully discharged battery or a  
new battery, allow the Battery Pack to  
Charge for at least 3 hours.  
do not charge the Battery Pack  
longer than 5 hours.  
2. Allow the Battery Pack to cool  
completely before charging.  
make sure the battery pack is  
undamaged; do not charge a  
cracked or leaking battery pack.  
WARNING! time the charging cycle.  
the battery charger will not signal  
when charging is finished.  
3. Disconnect the Cord from the  
Charger. Attach the plug to a  
grounded, 120 V~, 60 Hz outlet.  
7. Unplug the Charger and disconnect it  
from the Battery Pack when finished.  
8. Allow the Battery Pack to cool  
completely before using it.  
charger  
Battery  
Pack  
9. Store the Charger and Battery Pack  
indoors, out of reach of children.  
Figure 4a  
reV 09h  
Page 6  
For technical questions, please call 1-800-444-3353.  
SKU 67031  
 
PleaSe read the  
FolloWing careFully  
uSer-maintenance  
inStructionS  
THE MANUFACTURER AND/OR  
DISTRIBUTOR HAS PROVIDED  
THE PARTS LIST IN THIS MANUAL  
AS A REFERENCE TOOL ONLy.  
NEITHER THE MANUFACTURER  
OR DISTRIBUTOR MAKES ANy  
REPRESENTATION OR WARRANTy OF  
ANy KIND TO THE BUyER THAT HE  
OR SHE IS qUALIFIED TO MAKE ANy  
REPAIRS TO THE PRODUCT, OR THAT  
HE OR SHE IS qUALIFIED TO REPLACE  
ANy PARTS OF THE PRODUCT. IN  
FACT, THE MANUFACTURER AND/  
OR DISTRIBUTOR ExPRESSLy  
STATES THAT ALL REPAIRS AND  
PARTS REPLACEMENTS SHOULD  
BE UNDERTAKEN By CERTIFIED  
AND LICENSED TECHNICIANS, AND  
NOT By THE BUyER. THE BUyER  
ASSUMES ALL RISK AND LIABILITy  
ARISING OUT OF HIS OR HER REPAIRS  
TO THE ORIGINAL PRODUCT OR  
REPLACEMENT PARTS THERETO,  
OR ARISING OUT OF HIS OR HER  
INSTALLATION OF REPLACEMENT  
PARTS THERETO.  
Procedures not specifically  
explained in this manual must  
be performed only by a qualified  
technician.  
to PreVent  
SeriouS injury  
From accidental  
oPeration:  
unplug the charger before  
performing any inspection,  
maintenance, or cleaning  
procedures.  
to PreVent SeriouS  
injury From charger or  
Battery Pack Failure:  
do not use damaged charger/  
battery pack.  
1. BeFore each uSe, inspect the  
general condition of the Charger.  
Check for loose hardware, cracked  
or broken parts, damaged electrical  
wiring, and any other condition that  
may affect its safe operation.  
2. aFter uSe, wipe external surfaces  
of the Charger with clean, cloth.  
PartS liSt  
3. ni-cd Battery muSt Be  
recycled or diSPoSed  
Part  
1
description  
Charger  
oF ProPerly. do not short,  
incinerate or open Battery Pack.  
2
AC/DC Adapter  
record Product’s Serial number here:  
Note: If product has no serial number,  
record month and year of purchase  
instead.  
Note: Some parts are listed for illustration  
purposes only, and are not available  
individually as replacement parts.  
SKU 67031  
For technical questions, please call 1-800-444-3353.  
Page 7  
 
To take advantage of this warranty,  
the product or part must be returned to us  
with transportation charges prepaid. Proof  
of purchase date and an explanation of the  
complaint must accompany the merchan-  
dise. If our inspection verifies the defect,  
we will either repair or replace the product  
at our election or we may elect to refund  
the purchase price if we cannot readily  
and quickly provide you with a replace-  
ment. We will return repaired products at  
our expense, but if we determine there  
is no defect, or that the defect resulted  
from causes not within the scope of our  
warranty, then you must bear the cost of  
returning the product.  
limited 90 day Warranty  
Harbor Freight Tools Co. makes ev-  
ery effort to assure that its products meet  
high quality and durability standards, and  
warrants to the original purchaser that this  
product is free from defects in materials  
and workmanship for the period of 90 days  
from the date of purchase. This warranty  
does not apply to damage due directly or  
indirectly, to misuse, abuse, negligence or  
accidents, repairs or alterations outside  
our facilities, criminal activity, improper  
installation, normal wear and tear, or to  
lack of maintenance. We shall in no event  
be liable for death, injuries to persons  
or property, or for incidental, contingent,  
special or consequential damages arising  
from the use of our product. Some states  
do not allow the exclusion or limitation  
of incidental or consequential damages,  
so the above limitation of exclusion may  
not apply to you. THIS WARRANTy IS  
ExPRESSLy IN LIEU OF ALL OTHER  
WARRANTIES, ExPRESS OR IMPLIED,  
INCLUDING THE WARRANTIES OF  
MERCHANTABILITy AND FITNESS.  
This warranty gives you specific  
legal rights and you may also have other  
rights which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box  
6009 • Camarillo, CA 93011 • (800)  
444-3353  
Page 8  
For technical questions, please call 1-800-444-3353.  
SKU 67031  
 

Greenheck Fan Ventilation Hood Vektor H User Manual
Grizzly Cordless Sander g5344 User Manual
Groupe SEB USA T FAL Iron FV4020 User Manual
Havis Shields Network Card C 3065 3 User Manual
Honeywell Cell Phone 805595 User Manual
Hoshizaki Ice Maker KML 200MAE User Manual
HP Hewlett Packard Network Cables 441877 00F User Manual
IBM Computer Drive x Series 200 User Manual
IBM Printer HL 5240 User Manual
IKEA Dishwasher DW60 User Manual