Harbor Freight Tools Saw 92639 User Manual

SLIDE HAMMER  
FOR AUTO BODY WORK  
92639  
ASSEMBLY AND OPERATING INSTRUCTIONS  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
©
®
Copyright 2005 by Harbor FreightTools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or  
form without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
9.  
Maintain tools with care. Keep tools clean for better and safer performance. The  
handle must be kept clean, dry, and free from oil and grease at all times.  
10. Stay alert. Watch what you are doing, use common sense. Do not operate any tool  
when you are tired.  
11. Check for damaged parts. Before using any tool, any part that appears damaged  
should be carefully checked to determine that it will operate properly and perform its  
intended function. Check for alignment and binding of moving parts; any broken parts  
or mounting fixtures; and any other condition that may affect proper operation. Any  
part that is damaged should be properly repaired or replaced by a qualified  
technician.  
12. Replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty. Only use accessories  
intended for use with this tool. Approved accessories are available from Harbor  
Freight Tools.  
13. Do not operate tool if under the influence of alcohol or drugs. Read warning  
labels if taking prescription medicine to determine if your judgment or reflexes are  
impaired while taking drugs. If there is any doubt, do not operate the tool.  
14. Maintenance. For your safety, service and maintenance should be performed  
regularly by a qualified technician.  
15. Secure vehicle. Make sure the vehicle engine is off, the transmission is in gear or  
park, and the emergency brake is set, before starting repairs.  
Warning:The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be under-  
stood by the operator that common sense and caution are factors which cannot be  
built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking, check to make sure the parts listed on page 5 are included. If any parts  
are missing or broken, please call Harbor Freight Tools at the number on the cover of this  
manual as soon as possible.  
SKU 92639  
For technical questions, please call 1-800-444-3353  
Page 3  
 
Operation  
FIGURE 1  
Slide (3)  
Handle (4)  
Cone Head (5)  
Shaft (1)  
Wedge Head (6)  
Hook Head (8)  
Round Head (7)  
Knurled Nut  
The results achieved with this tool rely largely on the skill of the operator.  
Harbor Freight Tools is not responsible for any damage caused by inexperience or  
by misuse of this tool. Harbor Freight Tools recommends that this tool should be  
used only by experienced auto body repair professionals.  
Hook Pulling  
1.  
2.  
Identify the area you will be inserting the Hook Head (8) into or onto.  
Back the Knurled Nut to the end of the Hook Head (8). Thread the Knurled Nut onto  
the Shaft (1).  
3.  
4.  
Place the Hook Head (8) tip onto the edge or lip of the object to be pulled.  
Gripping the Handle (4) securely with one hand, and the Slide (3) with the other, firmly  
pull the Slide (3) toward the Handle end of the Slide Hammer.  
5.  
Repeat pulling the Slide (3) until the object has been pulled out.  
Hammering (Pushing in dents)  
1.  
2.  
Identify the area you will be hammering onto.  
Depending on the shape of the metal you are hammering or pushing in, choose either  
the Wedge (6), Round (7), or Cone (5) Head.  
3.  
4.  
Thread the Head onto the Shaft (1).  
Gripping the Handle (4) securely with one hand, and the Slide (3) with the other, firmly  
push the Slide (3) toward the end of the Shaft (1) with the head (into the dent).  
5.  
Repeat pushing the Slide (3) until the dent is pushed in.  
SKU 92639  
For technical questions, please call 1-800-444-3353  
Page 4  
 
Maintenance  
1.  
2.  
3.  
After each use, wipe the unit down with a lint free cloth.  
After using the Heads or Hook, wipe them clean of any dirt or debris.  
Keep the Handle (4) clean and dry.  
Parts List  
Part No.  
Description  
Shaft  
Block  
Slide  
Handle  
Cone Head  
Wedge Head  
Round Head  
Hook Head  
1
2
3
4
5
6
7
8
PLEASE READTHE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-  
TOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTO THE BUYERTHAT HE  
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
SKU 92639  
For technical questions, please call 1-800-444-3353  
Page 5  
 
Assembly Drawing  
SKU 92639  
For technical questions, please call 1-800-444-3353  
Page 6  
 

Groupe SEB USA T FAL Iron FV21XX series User Manual
Havis Shields Automobile Accessories KK F VAK User Manual
Hotpoint Clothes Dryer THDP 871 User Manual
Hotpoint Dishwasher HDA2000ZAD User Manual
Hotpoint Microwave Oven MWH211 User Manual
HP Hewlett Packard All in One Printer P1000 series User Manual
Huey Chiao Bluetooth Headset HCB25 User Manual
Huey Chiao Network Card HCB 21 User Manual
IBM Computer Drive 22P6979 User Manual
Ice O Matic Ice Maker ICE1506 Series User Manual