Honeywell Stereo System High Gain Omni Directional Antenna User Manual

High Gain Omni Directional  
Antenna User Guide  
Honeywell  
Industrial Measurement and Control  
2500 W. Union Hills Drive  
Phoenix AZ, 85927  
34-XY-25-10  
Rev 4  
0806  
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
Rev. 4  
0806  
User Manual  
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
1. About the High Gain Omni Directional  
Antenna  
High gain and remote antennas can increase the transmission distance of the  
Honeywell Wireless Sensors. For even greater transmission distance, a high gain  
directional antenna (Yagi) may be purchased as an integral part of a field unit.  
Any Base Radio with an Omni Directional antenna is for  
ordinary locations only.  
This manual will guide you through the steps to connect a High Gain Omni  
Directional Antenna with or without a lightning arrestor to a Base Radio. If you  
are using a lightning arrestor, go to section 2. If you are not using a lightning  
arrestor, go to section 3.  
The following model numbers are covered in this guide. Both Base Radios  
models can be used with any of the High Gain Remote Antenna models below.  
Antennas  
Description  
HBW-00-TE-HA-9X  
NEMA 4X Base Radio w/10 ft cable, RS-485 & Modbus, for rmt  
antenna with Omni Directional 6 dBd Pole remote antenna  
HBW-00-TE-HB-9X  
HBW-00-TE-HC-9X  
NEMA 4X Base Radio w/10 ft cable, RS-485 & Modbus, for rmt  
antenna with Omni 6 dBd remote antenna w/lightning arrestor & 10 ft  
cable  
NEMA 4X Base Radio w/10 ft cable, RS-485 & Modbus, for rmt  
antenna with Omni 6 dBd remote antenna w/lightning arrestor & 25 ft  
cable  
HBW-00-TW-HA-9X  
HBW-00-TW-HB-9X  
NEMA 4X Base Radio w/25 ft cable, RS-485 & Modbus, for rmt  
antenna with Omni Directional 6 dBd Pole remote antenna  
NEMA 4X Base Radio w/25 ft cable, RS-485 & Modbus, for rmt  
antenna with Omni 6 dBd remote antenna w/lightning arrestor & 10 ft  
cable  
HBW-00-TW-HC-9X  
NEMA 4X Base Radio w/25 ft cable, RS-485 & Modbus, for rmt  
antenna with Omni 6 dBd remote antenna w/lightning arrestor & 25 ft  
cable  
Rev. 4  
0806  
User Manual  
1
 
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
Rev. 4  
0806  
User Manual  
2
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
2. Installing the High Gain Antenna with the  
Lightning Arrestor  
This section will show you how to install the high gain antenna with the  
lightning arrestor. If you are not using the lightning arrestor, go to Section 3. For  
additional information about the Base Radio see the Base Radio User Manual.  
Any of the Base Radio model numbers mentioned in section 1 may be used with  
the following remote antenna models:  
WBH-00-TE-HB-9X Omni 6 dBd remote antenna w/lightning arrestor &  
10 ft cable  
WBH-00-TE-HC-9X Omni 6 dBd remote antenna w/lightning arrestor &  
25 ft cable  
WBH-00-TW-HB-9X Omni 6 dBd remote antenna w/lightning arrestor &  
10 ft cable  
WBH-00-TW-HC-9X Omni 6 dBd remote antenna w/lightning arrestor &  
25 ft cable  
2.1. Package Contents  
The high gain Omni 6 dBd antenna with the lightning arrestor kit comes  
complete with:  
[1]  
[2]  
[3]  
High gain antenna pole  
2 Mounting brackets for the high gain antenna  
Lightning arrestor assembly consisting of lightning arrestor and 10’ of 10  
AWG ground wire  
[4]  
Coaxial cable assembly attached to the lightning arrestor:  
10’ length for the WBH-00-TE-HB-9X and WBH-00-TW-HB-9X  
25’ length for the WBH-00-TE-HC-9X and WBH-00-TW-HC-9X  
Waterproofing material for the antenna coaxial connection  
[5]  
The following comes attached to the Base Radio:  
[6]  
Coaxial cable assembly:  
10’ length for the WBH-00-TE-HB-9X and WBH-00-TE-HC-9X  
25’ length for the WBH-00-TW-HB-9X and WBH-00-TW-HC-9X  
Rev. 4  
0806  
User Manual  
3
 
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
2.2. Antenna & Lightning Arrestor Connection  
Attention!  
For installation in  
ordinary locations  
only.  
Antenna Connected to Lightning Arrestor and Base Radio  
Rev. 4  
0806  
User Manual  
4
 
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
Warning: Always use caution when installing this antenna. You can be  
seriously injured if this antenna comes near or in contact with a power line.  
Follow all local and national electrical code requirements when installing the  
Base Radio with the high gain antenna.  
[1]  
Select the locations for the high gain antenna, the lightning arrestor and  
Base Radio.  
Any Base Radio with an Omni Directional antenna is for  
ordinary locations only.  
It is recommended that the lightning arrestor be mounted in close  
proximity to the building egress. The lightning arrestor should be  
mounted indoors unless you have the weatherproof enclosure.  
The location for the high gain antenna should be selected based on  
optimal positioning for RF communications with the field units and allow  
for sufficient length of coaxial cable to reach the building egress.  
The Base Radio should be installed in a location where there is sufficient  
coaxial cable available to reach the building egress.  
[2]  
[3]  
Position the antenna so that the gold sleeve clears any obstructions.  
Mount the antenna using the  
2 mounting brackets. One  
clamp must be placed at the  
center of the gold sleeve, the  
other at any point below.  
[4]  
[5]  
Connect the Base Radio coaxial cable to the lightning arrestor and tighten  
by hand.  
Attach the ground wire to a suitable earth ground connection. Keep this  
wire as short as possible. Make sure this connection conforms to  
electrical code requirements.  
[6]  
[7]  
Connect the lightning arrestor coaxial cable to the antenna and hand  
tighten.  
Install a drip loop in the cable to insure proper drainage.  
[8] Wrap the antenna connection with the supplied waterproofing material.  
Note: Do not cover the drain holes on the bottom of the antenna as they  
provide drainage for moisture.  
[9]  
Finished.  
Rev. 4  
0806  
User Manual  
5
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
3. Installing the High Gain Antenna  
This section will show you how to install the high gain antenna without a  
lightning arrestor. If you are using a lightning arrestor, go to section 2. For  
additional information about the Base Radio see the Base Radio User Manual.  
This configuration is for indoor use only. If you are mounting  
the antenna outdoors, a lightning arrestor must be used.  
Any of the Base Radio model numbers mentioned in section 1 may be used with  
the following remote antenna model:  
WBH-00-TE-HA-9X Omni Directional 6 dBd Pole remote antenna  
WBH-00-TW-HA-9X Omni Directional 6 dBd Pole remote antenna  
3.1. Package Contents  
The high gain Omni 6 dBd antenna kit comes complete with:  
[1]  
[2]  
[3]  
High gain antenna pole  
2 Mounting brackets for the high gain antenna  
Waterproofing material for the antenna coaxial connection  
The following comes attached to the Base Radio:  
[4]  
Coaxial cable assembly:  
10’ length for the WBH-00-TE-HA-9X  
25’ length for the WBH-00-TW-HA-9X  
Rev. 4  
0806  
User Manual  
6
 
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
3.2. Antenna Connection  
Attention!  
For installation in  
ordinary locations  
only.  
Antenna Connected to Base Radio  
Rev. 4  
0806  
User Manual  
7
 
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
Warning: Always use caution when installing this antenna. You can be  
seriously injured if this antenna comes near or in contact with a power line.  
Follow all local and national electrical code requirements when installing the  
Base Radio with the high gain antenna.  
[1]  
Select the locations for the high gain antenna and Base Radio. The  
location for the high gain antenna should be selected based on optimal  
positioning for RF communications with the field units.  
Any Base Radio with an Omni Directional antenna is for  
ordinary locations only.  
[2]  
[3]  
Position the antenna so that the gold sleeve clears any obstructions.  
Mount the antenna using the  
2 mounting brackets. One  
clamp must be placed at the  
center of the gold sleeve, the  
other at any point below.  
[4]  
[5]  
Connect the Base Radio coaxial cable to the antenna and hand tighten.  
Wrap the connection with the supplied waterproofing material.  
Note: Do not cover the drain holes on the bottom of the antenna as they  
provide drainage for moisture.  
[6]  
Finished.  
Rev. 4  
0806  
User Manual  
8
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
4. Technical Specifications  
Base Radio High Gain Omni Directional Antenna  
Length  
65”  
Gain  
6 dBd (less cable loss 0.04 dBd/ft)  
Weight  
6 lbs  
Polarization  
Vertical  
Mounting  
Heavy wall gold anodized 1 ¼” aluminum with brackets included  
10’ or 25’  
Base Radio coaxial cable length  
Rev. 4  
0806  
User Manual  
9
 
 
Honeywell Industrial Wireless  
High Gain Omni-Directional Antenna  
Mounting Bracket Dimensioned Drawing  
Rev. 4  
0806  
User Manual  
10  
 
 
*17414*  
Honeywell  
Industrial Measurement and Control  
2500 W. Union Hills Drive  
Phoenix AZ, 85927  
 

Grindmaster Hot Beverage Maker CC 302 20 User Manual
Grizzly Saw G0636X User Manual
Hamilton Beach Toaster 22790 User Manual
HANNspree Flat Panel Television F651 12U1 000 User Manual
HANNspree Graphics Tablet SN1AT75HSG1310 User Manual
Hotpoint Mixer PC25357 User Manual
Hotpoint Washer Dryer HF8B User Manual
HP Hewlett Packard All in One Printer 510PS User Manual
HP Hewlett Packard Switch SAS BL User Manual
i Tech Dynamic Headphones Clip D Radio User Manual