Husqvarna Lawn Mower Accessory H354SLG User Manual

OWNER’S MANUAL  
Model Number H354SLG  
Mfg. ID No. 96073002100  
Product No. 960 73 00-21  
54 Inch Mower  
Grass Catcher  
• Assembly  
• Operation  
• Customer Responsibilities  
• Repair Parts  
532420910 05.06.08 TH  
Printed in U.S.A.  
 
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
If you strike a foreign object, stop and inspect the  
IV. TOWING  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
Maintain or replace safety and instruction labels, as  
necessary.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
To avoid personal injury or property damage, use extreme  
careinhandlinggasoline. Gasolineisextremelyflammable  
and the vapors are explosive.  
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Alwayslookdownandbehindbeforeandwhilebacking.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Be alert and turn machine off if a child enters the  
area.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine  
running. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Remove gas-powered equipment from the truck or  
trailer and refuel it on the ground. If this is not possible,  
then refuel such equipment with a portable container,  
rather than from a gasoline dispenser nozzle.  
Keepthenozzleincontactwiththerimofthefueltankor  
container opening at all times until fueling is complete.  
Do not use a nozzle lock-open device.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
GENERAL SERVICE  
Never operate machine in a closed are.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any  
fuel-soaked debris. Allow machine to cool before  
storing.  
CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to  
give you the best possible dependability and performance.  
Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center/  
department. They have competent, well trained technicians and the proper tools to service or repair this unit.  
Please read and retain this manual. The instructions will enable you to assemble and maintain your Grass Catcher properly.  
Always observe the "SAFETY RULES".  
TABLE OF CONTENTS  
SAFETY RULES ................................................................... 2-3  
CARTON CONTENTS ............................................................. 4  
ASSEMBLY........................................................................... 5-8  
OPERATION ............................................................................ 8  
CUSTOMER RESPONSIBILITIES........................................... 9  
STORAGE................................................................................ 9  
REPAIR PARTS ..................................................................... 10  
3
 
KNOW YOUR GRASS CATCHER  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS  
CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the  
assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass  
Catcher and to prevent injury to yourself and others. Save this manual for future reference.  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe  
eye damage. Always wear safety glasses or eye shields before starting your tractor and while mowing.  
We recommend a wide vision safety mask for over the spectacles or standard safety glasses.  
COMPLETE BAGGER MUST BE IN PLACE BEFORE OPERATING MOWER  
UNPACKING INSTRUCTIONS  
CARTON CONTENTS:  
Remove all parts and packing materials from carton.  
(1) Cover Assembly  
(1) Retainer Spring  
(2) Shoulder Bolts  
(3) Containers  
Check carton contents against list. Be sure all parts  
are there.  
(1) Upper Chute  
(1) Lower Chute  
(2) Support Assembly  
SHOULDER  
BOLTS  
PARTS IDENTIFICATION  
SUPPORT  
ASSEMBLY  
(VERTICAL  
DRAWBAR)  
COVER  
FULL BAG  
INDICATOR  
RETAINER  
SPRING  
CHUTE  
LATCH  
UPPER  
CHUTE  
SUPPORT  
ASSEMBLY  
(SLOPED  
GRASS  
CATCHER  
CONTAINERS  
LOWER CHUTE  
LOWER CHUTE  
ATTACHING  
STRAPS  
RETAINER  
SPRING  
DRAWBAR)  
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the  
tractor, in the operator's position.  
CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR:  
Depress clutch/brake pedal fully and set parking brake.  
Place gearshift/motion control lever in "NEUTRAL" position.  
Place attachment clutch in "DISENGAGED" position.  
Turn ignition key "OFF" and remove key.  
Make sure the blade and all moving parts have completely stopped.  
Disconnect spark plug wire from plug and place where it cannot come in contact with plug.  
4
 
ASSEMBLY  
2. Align support assembly pin with hole in drawbar and  
BAGGER SUPPORT ASSEMBLY  
hang assembly over the shoulder bolts.  
1
3. Besuresupportassemblyisseatedproperlyandsecure  
Determine which type drawbar you have on your tractor.  
Compare the drawbar illustrations below to the drawbar  
located at the rear of your tractor.  
with retainer spring supplied.  
SHOULDER  
BOLTS  
Follow the support assembly instructions that apply to your  
type drawbar.  
SUPPORT  
ASSEMBLY  
DRAWBAR B  
(Sloping Drawbar)  
DRAWBAR A  
(Vertical Drawbar)  
DRAWBAR A (See Figs. 1A, 1B & 1C)  
1. Remove and discard the upper bolt on both sides of  
the drawbar. Using the same holes, install the shoulder  
bolts supplied and tighten securely.  
RETAINER  
SPRING  
FIG. 1C  
DRAWBAR B (See Fig. 1D)  
REMOVE AND DISCARD  
UPPER BOLTS AND INSTALL  
SHOULDER BOLTS SUPPLIED  
1. Slide flanges of support assembly into drawbar slots first,  
then, pivot backwards inserting pin into drawbar pin hole.  
2. Besuresupportassemblyisseatedproperly,thensecure  
with retainer spring.  
SUPPORT  
ASSEMBLY  
DRAWBAR SLOTS  
31  
5
2
0
DRAWBAR  
FIG. 1A  
INSERT  
FLANGES  
FIRST INTO  
DRAWBAR  
SLOTS  
PIN  
DRAWBAR  
PIN HOLE  
RETAINER  
SPRING  
FIG. 1D  
FIG. 1B  
5
 
MOUNTING COVER ASSEMBLY TO  
SUPPORT ASSEMBLY (See Fig. 2)  
NOTE: For ease of assembly, you may wish to obtain the  
assistance of another person for mounting cover assembly  
to tractor.  
CONTAINER MOUNTING (See Fig. 3)  
3
2
1. Install one container to left side first. Install another  
container to center position and one in right position.  
NOTE: Left edge of right container should always overlap  
right edge of left container at center supports.  
2. Close cover and lock latches over center support  
tubes. To lock and release latches, pull back on latch  
handles.  
1. Position cover assembly on ground behind tractor.  
2. Liftandrotatecovertoaligncoverbracketswithsupport  
assembly tubes.  
3. Slide cover assembly down onto the support tubes.  
COVER LATCH  
HANDLES  
COVER  
ASSEMBLY  
SUPPORT  
ASSEMBLY  
CENTER  
CONTAINER  
SUPPORT  
HANDLES  
TUBES  
FIG. 3  
03024  
FIG. 2  
6
 
LOWER CHUTE (See Fig. 4)  
UPPER CHUTE (See Figs. 5A and 5B)  
4
5
1. Raise and hold deflector shield in upright position.  
1. Lower mower to its lowest cutting position.  
2. Place slot in lower chute over mounting tab on mower  
and position lower chute over mower opening as  
shown.  
2. Assemble upper chute by inserting curved end into  
hole in back of cover.  
TIP: Holding upper chute as shown and twisting while  
installing in cover will help keep the rubber seal in place.  
3. Hook rear latch into flange hole on back of mower.  
4. Hook front latch into hole in front gauge wheel bracket  
or under gauge wheel bracket on mower without a hole  
in the bracket.  
NOTE: Handle carefully so as not to damage full bag indi-  
cator.  
COVER  
UPPER CHUTE  
CAUTION: Do not remove deflector  
shield from mower. Raise and hold  
shield when attaching lower chute  
and allow it to rest on chute while in  
operation.  
DEFLECTOR  
SHIELD  
FIG. 5A  
3. Push in and turn upper chute until it is in line with lower  
chute.  
4. Align the bosses on lower chute with alignment slots  
on upper chute and slide together.  
5. Secure with rubber latch by hooking hole in latch over  
latch pin.  
COVER  
FULL BAG INDICATOR  
UPPER  
CHUTE  
MOUNTING  
TAB  
0
2
783  
HANDLE  
LATCH PIN  
REAR LATCH  
GAUGE WHEEL  
BRACKET  
RUBBER  
LATCH  
ALIGNMENT  
SLOT  
BOSSES  
LOWER CHUTE  
FIG. 5B  
FRONT  
LATCH  
LEVEL MOWER DECK  
6
Be sure deck is properly leveled for best mower  
performance. See your tractors owner's manual for  
instructions.  
FIG. 4  
7
 
OPERATION  
Your bagger is equipped with a full bagger indicator.  
TIPS FOR IMPROVED BAGGING  
OPERATION:  
Movement of the wheel increases as the bags fill. The  
wheel will be spinning fastest just before the bags fill  
completely. When the wheel stops, it indicates that the  
bags are full and the chutes have become clogged.  
Follow the mower operation instructions in your tractor  
owner's manual.  
When operating your grass catcher on a lawn where grass  
and leaf bagging equipment has not been used, you are  
picking up thatch and debris that has accumulated for long  
periods of time. The amount collected and the total time  
of operation may be greater than you will experience with  
regular use of your grass catcher.  
NOTE: To help prevent clogging of chutes, check/empty  
bagswhenthewheelisspinningfast. Experiencewillteach  
you the best time to empty the bags.  
Care should be taken not to damage the parts and that  
the wheel spins freely at the beginning of each use.  
If the grass catcher fails to pick up cut grass or leaves,  
it is an indication that clogging has occurred in the  
system or that the grass catcher containers are full.  
Usually this is indicated by the stopped movement of  
the full bagger indicator.  
Always run throttle at full speed when bagging.  
Select a gear low enough to give good mower cutting  
performance, good quality cut and good bagging  
performance.  
NOTE: It may be necessary to overlap width of cut to suit  
your conditions.  
a. Disengage blades, shift into neutral, engage the  
parking brake and stop the engine.  
If grass is extremely tall, it should be mowed twice. The  
first time relatively high, the second time to desired  
height.  
- Raise seat. Unlatch and raise cover.  
- Slide out containers and dispose of clippings .  
- Replace containers, close cover, and latch.  
b. Unlatch chutes and check for clogging.  
- Remove all debris in chutes.  
- Reassemble and latch chutes  
c. Checktoinsurefullbaggerindicatorhasnotbecome  
clogged.  
Use left hand side of mower for trimming.  
Plastic trash bags can be inserted inside grass catcher  
containers for ease of debris disposal. To remove the  
plastic trash bags when full:  
a. Disengage blades, shift into neutral, engage the  
parking brake and stop the engine.  
b. Raise seat. Unlatch and raise cover.  
- The air passage hole must be clear of debris.  
Gentlyinsertasmalltwigorwireintopassageway  
to clear.  
c. Remove one container at a time by grasping  
container handles and pulling toward the rear, off  
of the tube rails.  
d. With the container resting on the ground, close  
CAUTION  
and secure the top of the plastic lawn bag.  
e. Tip the container on its side and slide the filled bag  
from the container.  
• Do not operate mower with grass catcher  
partially installed.  
• Disengage blades and stop engine before  
leaving tractor seat to empty containers,  
unclogging chutes, etc.  
f. Install a new plastic lawn bag with the edges of  
the bag draped over upper lip of the container.  
g. Repeat for other containers.  
h. Reinstall containers making sure right container  
overlaps left container at center supports.  
• Close cover before starting.  
j. Closecoverandsecurelatchesovercentersupport  
tubes.  
Avoid cutting wet grass or in the morning while the dew  
is still heavy. Grass clippings collected under these  
conditions tend to be sticky and adhere to the walls of  
the flow path causing clogging.  
• Disengage mower when crossing driveways  
or gravel surfaces and other areas where  
thrown objects could be a hazard.  
• Do not attempt to vacuum up cans or other  
potentially hazardous projectiles.  
8
 
CUSTOMER RESPONSIBILITIES  
GENERAL RECOMMENDATIONS  
CAUTION: Grass catcher components  
are subject to wear, damage and  
deterioration, which could expose  
moving parts or allow objects  
to be thrown. Frequently check  
components and replace with  
manufacturer's recommended parts,  
when necessary.  
Always observe safety rules when performing any main-  
tenance.  
Before each use check for loose fasteners.  
Clean unit thoroughly after each use.  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
See BLADE CARE instructions in your tractor owner's  
manual.  
STORAGE  
When grass catcher is to be stored for a period of time,  
clean it thoroughly, remove all dirt, grass, leaves, etc. Store  
in a clean, dry place.  
CAUTION:BEFOREPERFORMINGANY  
MAINTENANCE,SERVICEORADJUST-  
MENTS:  
CAUTION: Donotleavegrassinbagger  
containers. Emptycontainersaftereach  
useandbeforestoring. Failuretodoso  
mayresultinspontaneouscombustion  
which could develop into a fire.  
Depress clutch brake pedal fully and  
set parking brake.  
Place gearshift/motion control lever in  
"NEUTRAL" position.  
Placeclutchcontrolin"DISENGAGED"  
position.  
Turn ignition key to "OFF" position.  
Make sure blades and all moving parts  
have completely stopped.  
Disconnect spark plug wire(s) from  
spark plug(s) and place wire where it  
cannot come in contact with plug.  
9
 
REPAIR PARTS  
GRASS CATCHER - MODEL NUMBER H354SLG MFG. ID NO. 96073002100  
(PRODUCT NO. 960 73 00-21)  
ꢂꢃ  
ꢅꢃ  
ꢅꢇ  
ꢅꢅ  
ꢂꢃ  
ꢀꢇ  
ꢀꢇ  
ꢅꢁ  
ꢂꢃ  
ꢂꢃ  
ꢀꢆ  
ꢀꢉ  
ꢅꢂ  
ꢅꢀ  
ꢀꢀ  
ꢅꢆ  
ꢅꢁ  
ꢂꢈ  
ꢅꢂ  
ꢅꢆ  
ꢀꢂ  
ꢀꢅ  
ꢀꢀ  
ꢂꢇ  
ꢂꢄ  
ꢀꢅ  
ꢂꢄ  
ꢀꢃ  
ꢂꢉ  
ꢀꢁ  
ꢀꢃ  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
2
3
4
5
6
7
8
9
532069180  
Nut, Crownlock #10-24  
Screen, Cover  
20 871161010  
26 532004939  
Screw #10-24 x 5/8  
Spring, Retainer  
Support Assembly  
Support Assembly  
Shoulder Bolt  
Spring, Retainer  
Plug, Tubing End  
Bagger, Frame  
Pin, Hinge  
Gasket, Cover  
Container  
Seal, Cover  
Latch Handle, Cover  
532192709  
532195373  
532187299  
818021008  
532130933  
532087175  
532052784  
Cover Assembly (Includes 34, 37) 27 532414445  
Chute, Upper  
28 532420732  
29 532176997  
30 532165898  
31 532174083  
32 532414444  
33 532192786  
34 532192550  
35 532400226  
37 532192603  
38 532130895  
Screw, Special #10-14 x 1/2  
Full Bag Indicator  
Screw, #10-24 x 1-1/8  
Washer 3/16 x 3/4 x 16 Ga.  
Spacer, Split  
10 532007206  
11 532060867  
12 810071000  
13 532109808  
14 532125004  
15 532160793  
18 532187300  
Nut, Acorn #10-24  
Washer, lock  
Latch, Chute  
Nut, Weld  
Latch  
Chute, Lower  
10  
 

Graco Home Theater Server 24M224HP User Manual
Graco Marine Instruments 309868D User Manual
Grindmaster Coffeemaker AM 344 04 User Manual
Hoshizaki Ice Maker IM 51BAE User Manual
Hotpoint Washer AQ113F 497 I User Manual
Hotpoint Washer aqm8l 29 l User Manual
HP Hewlett Packard Network Cables 8505A User Manual
Husqvarna Cordless Saw K750 User Manual
hussman Carrying Case DCCG User Manual
Impex Home Gym MP 3105 User Manual