Digital Housing
i n s t r u c t i o n m a n u a l
f o r
Sony
DSC-V1
H o u s i n g
#6110.91
CClloossiinngg tthhee HHoouussiinngg
1. Place housing face down in your
lap.
CChheecckkiinngg CCoonnttrroollss
housing back
Once the housing has been closed, push the controls back into
place. Make sure they line up with the camera’s controls.
2. Check to see that there is an
o’ring on the housing back and
that it is clean and in its proper
location.
3. Guide the back onto the housing.
The o’ring should touch the
housing all the way around. There
should be an even gap all the way
around between the housing and
the housing back.
TTuurrnn CCaammeerraa OOnn
Turn the camera on and operate each of the housing controls to
get a feel for using the camera in the housing. Take a few
pictures above water with the camera in the housing.
o’ring
housing
JJoogg DDiiaall CCoonnttrrooll
The housing’s Jog Dial
Control has a small bump
on the inside face of the
control for depressing the
Jog Dial on the camera.
The small bump is in the
same location as the
4. Lift the lid snaps so they are
extended and place the lid snap
into the hook on the housing
back.
housing back
Jog Dial
5. To close the housing push
down on the lid snaps until
they snap into place . Lid
even gap
all 4 sides
white dot on the control
knob. To use, rotate the
control knob until the
white dot is in the 9
o’clock position. In this
position the small bump will depress the Jog Dial.
Control
Button
Back of Housing
snaps on opposite sides of the
housing should be closed at the
same time. Be sure they are down
far enough to engage the lock.
o’ring
housing
Double chheck - Once the housing is closed, check the o’ring seal.
Check the gap between the housing back and the housing, it
should be even all the way around.
Look through the clear plastic back at the o’ring. You should see a
darkened area where the o’ring is compressed against the
housing back. If you do not see an even black compression seal
all the way around the back, open the lid snaps, reseat the
housing back and close the lid snaps. Visually check the seal again.
To select an item turn the jog dial to the item you want to set.
Then pull out on the control slightly and position the white dot
over the jog dial and depress. This will set the item you selected.
5
6
QQuuiicckk--RReelleeaassee BBaassee,, HHaannddlleess aanndd TTrraayy
Quickk-Rellease Base
Quick Release Base
The Quick-Release Base is
Slot
plastic. A toggle lever located
underneath the base allows
the base to be easily removed
from the Tray. Turn the
housing upside down, pull
out on the toggle lever.
Rotate the lever 90° to
remove the base.
Flip Quick Release
Lever Up
Handless and Tray
The housing handles are
rubber and the tray is
aluminum. Their weight
helps to offset the buoyancy
of the housing. The complete
assembly is slightly negative
underwater for better
control. The handles have a
push button release for easily
Rotate Quick
Release Lever
attaching and removing
strobe arms. The tray and
handles can be removed from
the housing. To remove the
tray, the base must be
removed to gain access to
the nuts holding the tray on
the housing. Remove the 2
nuts, washers and rubber
spacers. DO NOT remove the
Remove Quick
Release Lever
bolts protruding through the
housing.
and Base
7
This edge against
housing
LLuubbrriiccaannttss
DDiiffffuusseerr aanndd DDeefflleeccttoorr ccoonntt..
A diffuser and deflector are
included with the housing. The
diffuser is white transparent
plastic. The deflector is also white
but is not transparent and has a
decal on the front.
Diffuser or
Deflector
material
1. Ikelite provides silicone lubricant with the housing. We
recommend that you use only Ikelite lubricant on Ikelite
products as some other brands may cause the o’ring to swell
and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and
o’rings. Wipe off any excess lubricant with a clean cloth.
Lubricant is not a sealant, it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing.
To install the diffuser or deflector
spread the port clamp at the spring
end and slide over the lens port.
The white plastic should be placed
in front of the camera flash. The
port clamp should be pushed back
against the front of the housing.
Port Clamp
Spring
CAUTION
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
Spread to Install
DDiiffffuusseerr
The diffuser should be installed when using the camera’s built in
flash. When shooting with the camera’s built-in flash at
approximately 2 feet (0.6 m) or less, zoom the lens to
maximum telephoto. The lens port on the housing blocks a
portion of the light from the camera’s built-in flash when
shooting close up. If you do not zoom to maximum telephoto, a
shadow may appear in the lower left corner of close-up
photographs. (You can test this above water)
DDiiffffuusseerr aanndd DDeefflleeccttoorr IInnssttaallllaattiioonn
Diffuser
DDeefflleeccttoorr
The deflector should be installed when using an external strobe
such as the DS51 or DS125 Substrobe and EV-Controller in the
slave mode. The deflector will redirect the camera’s flash to the
EV-Controller which controls the external strobe.
Housing shown
with diffuser
installed.
8
9
LLeennss PPoorrtt
MMaaiinntteennaannccee
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
The Lens Port is factory sealed, do not remove.
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the lens port to avoid water spotting. To clean
use a mild soap solution or lens cleaner.
Do Not
1.
leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
Do not use alcohol or window cleaner on the Lens Port.
2. Do Nott ship the camera in the housing.
3. Before using the housing, always check the tightness of the
screw in each control knob.
The Lens Port is threaded so that accessory lenses may be
screwed onto the port. The threads are very fine, take care not
to cross thread the lens.
set
controol gland
Check each
penetrating the housing to make sure
Wide angle lenses are available from Inon, Sea & Sea and Epoque.
These lenses can be screwed onto the lens port above or below
water. These lenses are designed to have water between the
front of the port and the accessory lens. Make sure no air
bubbles are trapped between the port and the accessory lens.
There may be slight vignetting when these wide angle lenses
they are tight. There is a slight chance that either could vibrate
loose during travel.
4. Keep the back o’ring clean and lightly lubricated. To lubricate
remove the o’ring from the back. Put a small amount of lkelite
lubricant on your fingers. Draw the o’ring through your fingers
to apply a light coating of lubricant. Only apply enough
are installed. Any vignetting
Wide Angle
Lens
Do Not sstretcch the oo’ring
lubricant to make the o’ring feel slick.
.
that occurs can be eliminated
by zooming the camera lens
slightly. The camera’s built-in
flash cannot be used with
wide angle lenses. The front
of the lenses are so large
they block the camera’s
flash. To properly light
This light coating of lubricant will help to keep the o’ring from
drying out and will help to show a dark sealing line when the
housing back is properly sealed.
5. Keep the area where the o’ring fits and the sealing surface of
the housing clean.
6. Rinse the housing exterior thoroughly in fresh water after each
salt water use. Dry with a soft cloth. Dry lens port to eliminate
water spotting.
subjects when using a wide
angle lens an external strobe
should be used. Due to the
wide angle of coverage of
these lenses, the DS125
After several uses in salt water soak the housing in a mild soap
solution, rinse and dry before storage. When storing the
housing, remove the back o’ring, lightly lubricate and place in a
plastic bag. Place the plastic bag with o’ring inside the housing
for safe keeping.
Substrobe is recommended
or two DS51 Substrobes.
Housing shown with accessory
wide angle lens.
CCAAUUTTIIOONN
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
10
11
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
3. Some of the controls have a short shaft and cannot be pulled
out exposing the shaft for lubrication. In the unlikely event one
of these controls sticks or becomes difficult to operate you can
remove the control from the housing and lubricate it, or return
the housing to Ikelite for maintenance. To remove the control,
loosen the set screw in the knob (allen wrench required);
remove the knob. If there is salt or dirt build-up on the exposed
control shaft, clean the shaft. Open the housing and gently slide
the control shaft out of the control gland. Clean and lightly
lubricate the shaft, including the end of the shaft. Slide the
shaft back into the control gland and gently slide it back and
forth a few times without fully removing the shaft from the
gland. Replace the knob, NOTE the flat area on the shaft, the
set screw in the knob should tighten down against the flat area
on the control so the knob does not turn on the shaft.
CCoonnttrrooll MMaaiinntteennaannccee
Ikelite controls are designed to provide years of reliable service
with minimal maintenance.
1. Push button controls require no maintenance other than rinsing
in fresh water after saltwater use. If a push button control
becomes difficult to push or if it sticks when depressed, soak the
housing in luke warm fresh water. After a few minutes operate
the push button. If this does not correct the problem, return the
housing to Ikelite for maintenance.
2. Some of the controls have long shafts. These controls can be
lubricate shaft
housing
pull out to
expose shaft
housing
gland
control
shaft
pulled out, exposing the shaft (see drawing).
To lubricate the control, gently pull on the knob until the
stainless steel shaft is exposed. Lightly lubricate the shaft, then
move the shaft in and out several times. This will lubricate the
x’ring in the Ikelite control gland. This should be done before
using the housing after a prolonged storage period, or once a
week when the housing is in use.
Loosen set screw
(allen wrench required)
Flat
Tighten set screw down
against this area when
replacing the knob.
Lubricate end of shaft
before reinserting into
gland
12
13
OOppttiioonnaall AAcccceessssoorriieess
PPhhoottoo TTiippss
1. The number one rule in underwater photography is eliminate as
much water between camera and subject as possible. Get as
close as you can to the subject, then use the zoom. If you are
using flash, subjects beyond 6 feet (1.8m)will not have much
color.
BBaacckk OO''rriinngg ##00111100
O'rings last for several years if properly maintained.
(See Maintenance) Always carry a spare o'ring in case
the housing o'ring becomes damaged or lost.
UURR//PPrroo FFiilltteerr ##66444411..4411
2. If the camera’s built-in flash is being used it is very close to the
camera lens. The flash will light up any suspended particles in
the water and they will be recorded in your picture. This effect
is called backscatter. To eliminate as much backscatter as
possible, photograph close. Photograph in clear water; do not
stir up the sand or silty bottom. If backscatter becomes a
problem in the environment you are photographing, an external
flash will help eliminate much of the backscatter.
3. Digital cameras have a slight lag time between when you press
the shutter release button and the camera actually takes the
picture. Hold the camera steady a second or two after pressing
the shutter release button.
4. Do not shoot down on subjects as they will quite often blend
into the background and be difficult to see in the photograph.
Shoot subjects straight on or shoot up at a slight angle using
the blue water as a contrasting background.
5. Underwater flash is used to restore the warmer colors filtered
out by the water as well as to illuminate the subject. When
photographing underwater, set the camera to use flash on
every shot. If the camera’s flash is set to AUTO and the sun is
behind your subject, the camera may see enough light that it
does not fire the flash. With the sun behind the subject the
subject is shaded (dark) and needs flash for a good exposure.
EExxtteerrnnaall FFllaasshh
Using DS Suubstrroobes wiith thee EV-Coontroller.
The Ikelite EV-Controller provides 10 manual power settings in
half-stop increments with the DS51 or DS125 Substrobes. The
EV-Controller can be triggered by the camera's built-in flash or
the optional #4103 sync cord
attached to the housing
bulkhead.
Substrobe
DS51 or
External strobes expand lighting
options to achieve the best
lighting for different subjects.
A second external digital strobe
package can be added to fill
shadows and produce more
realistic photographs.
DS125
SA-100Q Arm
Usingg Ikelitte Subssttrobes
with Synnc Cords.
Any Ikelite Substrobe,
Substrobe 50, Substrobe DS51,
Substrobe 100, Substrobe DS125
or Substrobe 200 can be con-
nected to the housing and used
EV-Controller
in the manual mode with the #4103 sync cord.
14
15
GGeenneerraall TTiippss
1. Due to the power required to operate the camera, flash, and LCD
screen it is a good idea to start each dive with a fresh batteries.
2. Some cameras reset their flash to AUTO when the camera is
turned on. If you prefer another setting be sure to select it.
3. As soon as you enter the water, take a moment and check the
housing to see that it is properly sealed.
4. Next, check to see if there are any bubbles on the face of the
lens port. If there are, take your finger and remove them. If
there are bubbles on the lens port they can produce soft focus
spots in your photographs.
IIkkeelliittee LLiimmiitteedd WWaarrrraannttyy
All Ikelite products are warranted against any manufacturing
defects for a period of one (1) year from the date of purchase.
Defective products should be returned prepaid to Ikelite. Ikelite
will, at its discretion, repair or replace such products, and will
return to customer prepaid. All other claims, of any nature,
including but not limited to bulb failure are not covered. Except as
mentioned above, no other warranty expressed or implied, applies
to this Ikelite product.
RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviiccee
Ikelite is most interested in preforming any service to assure that
all products perform as intended. For repair or service, return
the product to the address below with your name, address,
phone number and a brief description of the problem. Evidence
of purchase date must be provided to obtain warranty service.
Ikelitte Underrwater SSystems
50 W 333rd Sttrreet • IIndiaanapolis, IIN 4622008 USA
317-923-44523 •• eemail:: ikeliite@ikkelite.com
Digittal 61100.91-0011-1003
|